Tie Down Anchors that Fit Top Channels of Rhino Rack Crossbars

Question

Question:

Im curious to know that size t-bolts I would need to mount tie down points to my Rhino Rack RTC. Would yall be able to help me with that? Thank you for your time.

asked by: Howard B

0

Expert Reply:

For the channels on top of Rhino Rack crossbars we have tie down anchors that fit into them with the part # S604. These won't fit into the tracks for the feet of your roof rack and at this time we don't have anything that would.

If you wanted anchor points for the underside of the crossbars you could use the part # RRS606 instead.

expert reply by: Jameson C

0

Answer 1

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 2

I measured the widths of the c-channel on the Rhino Rack Vortex Aero Crossbars and the bottom width is 7/8 inches and the neck width is 7/16 inches. I have attached a photo showing these measurements for you to check out. As long as the t-bolts on…

view full answer...

Answer 3

The thickness of the T-bolt head of the part #Y8880184 you referenced is 5/32 of an inch. I attached a picture that has all of the other dimensions as well. These T-bolts are M10 x 1.5 x 25

view full answer...

Answer 4

Rhino Rack square bars like the #RREB126B are 1-3/16 inches wide and 13/16 inches tall. Thule square bars like the part #TH712400 are 1-1/4 inches wide and 7/8 inches tall. So while they are very close to the same size they are different.

view full answer...

Answer 5

Yes, the track/channel dimensions between the Rhino Rack and Yakima roof racks are the same dimensions so the Yakima T-bolts part #Y8880184 that you referenced will fit and work well.

view full answer...

Answer 6

A similar bracket to the one that is pictured with the Mounting Kit for Rhino-Rack Foxwing Awnings #RR31105 can be found with Fit Kit part #RR31111. The mounting holes, center on center, are 2 inches apart.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Tie Down Anchors that Fit Top Channels of Rhino Rack Crossbars

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching