Does Grease Needed To Be Checked/Added In The Round A-Frame Trailer Jack TJA-5000-B?
Question:
Does it have grease zerks or the ability to grease it?
asked by: Dave B
Helpful Expert Reply:
The Round A-Frame Trailer Jack # TJA-5000-B you were looking at does not have grease zerks, nor is it greaseable. This is the same for all of the top wind A-Frame jacks we offer.
The reason for this is A-Frame jacks like this are sealed to keep debris and moisture out so grease does not need to be added. In addition the amount of revolutions the jack makes is nothing compared to components that need the grease changed such as a hub assembly on the trailer, so the grease does not really get worn down.
I included a video of the # TJA-5000-B for you to take a look at.
Products Referenced in This Question
Round A-Frame Trailer Jack - Topwind - 14-1/8" Travel - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Topwind Jack
- 14 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- etrailer
more information >
Product Page this Question was Asked From
Round A-Frame Trailer Jack - Topwind - 14-1/8" Travel - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Topwind Jack
- 14 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- etrailer
more information >
Continue Researching
- Shop: Round A-Frame Trailer Jack - Topwind - 14-1/8" Travel - 5,000 lbs
- Search Results: trailer jack
- Video: etrailer and Ram Jacks Drop Leg Review
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Shop: Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter Footplate - Zinc
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Search Results: drop leg trailer jack
- Search Results: fulton drop leg
- Article: Trailer Jacks
- Search Results: fulton trailer jack parts
- Search Results: jacks
- Video: Review of Dexter Trailer Hubs and Drums - Pre-Greased 3500 LB - 84546UC3-EZ
- Video: Fulton Camper Jack - Stabilizer Jack - FSJ1-SJ2 Review
- Video: TruRyde Electric Brake Assembly Installation
- Video: etrailer Round A-Frame Trailer Jack Review TJA-5000-B
- Q&A: Does etrailer Drop Leg Fit 5,000 Pound Sidewind Jack
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Roof Rack
- Shop: Truck Bed Sliding Tray
- Shop: Pro Series Round, A-Frame Jack - Topwind - 14" Lift - 2,000 lbs
- Shop: Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision
- Shop: Fulton Drop-Leg Stabilizer Jack with Mounting Channel - Weld-On - 28" Leg - 13" Bracket -
- Video: etrailer A-Frame Trailer Coupler - Standard Coupler - CA-5210-B Review
- Video: etrailer Round A-Frame Trailer Jack Review TJA-2000-B
- Q&A: Will a 5,000 lb Trailer Jack be Easier to Crank than a 2,000 lb Jack
- Q&A: How to Tell Left and Right Side of a New Dexter Axle without Taking Off the Hubs or Brakes
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Q&A: How to Reset Zero Point Calibration on Lippert Ground Control 3.0
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)