Replacement Bearings for Dexter 2,800 lb Axle

Question

Question:

I have a lippert Axle LC135-SBSA-83.5-65.5-NOSP-US-L 545-7242-30PT-CAP 2800# . It has a 5 stub hub and a grease zerk in the ends of the axle , I am looking for the part # for wheel bearing set and seal.

asked by: David M

0

Expert Reply:

The bearings you would need are inner bearing # LM67048, outer bearing # L44649 with a # 10-42 seal.

We don't have this as a kit but you can order each individually.

expert reply by: Jameson C

0

Answer 1

We do have a solution for replacing your obsolete Dexter trailer axle but it isn't your standard trailer axle as none of ours matches that description. If you want to stick with a standard axle you need to contact a trusted trailer shop to have…

view full answer...

Answer 2

The diameter of your trailer axle will determine the size of the parts that you will need to order for an axle over under kit. If your axle is 3 inches diameter, the Dexter Trailer Springs Over-Under Conversion Kit, #K71-385-00, would be a great…

view full answer...

Answer 3

You will want the Replacement Brake Spring Set for Dexter 10" x 1-1/2" Electric Trailer Brake Assembly #K71-362-00. Then you will want the Replacement Trailer Brake Magnet Kit for 7" Brake Assemblies #BP01-068 due to the thinner hubs…

view full answer...

Answer 4

Many times Dexter hubs will fit on a Lippert axle, but Lippert does have a few axles out there with special spindle sizes. Every Lippert axle comes with a tag or plate on the axle that gives a serial number or NV number. If you can give me that…

view full answer...

Answer 5

What is the weight rating on your axle? I unfortunately don't have a way to see what bearings and seals your trailer uses but if you can let me know the weight rating and/or if you could measure the different dimensions of your spindle I can see…

view full answer...

Answer 6

There are really two reasons to replace a grease seal, if they are damaged or worn and leaking grease then that is an obvious factor. If you are replacing bearings it is usually best to replace the grease seals as well because although they may still…

view full answer...

Answer 7

The Dexter 8-283 is an obsolete 2800lb 10 x 1-1/2 inch hub that used a LM67048 inner and a L44649 outer bearing. Unfortunately, we don't have any hubs that would be compatible with the spindles on your axle. Your best bet at this point would be…

view full answer...

Answer 8

I have confirmed with my contacts at Dexter, and the Electric Brake Shoe part #bp04-065 that you referenced was used on a very specific Dexter 2,800 pound axle. The correct seal for this axle is the #10-42. This seal has an inner diameter of 1.75 and…

view full answer...

Answer 9

There is very little difference between the two. Both hub/drums are for a 7K axle, and have an 8 on 6-1/2 inch bolt pattern with 1/2 inch wheel studs. Either hub/drum includes the bearings, races, grease seal, lug nuts and E-Z Lube dust cap. The…

view full answer...

Answer 10

I called Dexter Axle and my contact said that the serial number (D 4526043) can be the same on a couple of different P-11 axle types because it relates to the plant that it was manufactured at. The brake kit and hub and drum assembly that my contact…

view full answer...

Answer 11

The bearings you would need are inner bearing #LM67048, outer bearing #L44649 with a #10-42 seal. We don't have this as a kit but you can order each individually. We contacted Dexter and they informed us that you axle was made specifically for…

view full answer...

Answer 12

The EZ Loader bearing kit 300-020885 contains bearings for a BT8 spindle so the kit you'd need is the part #BK1-150.

view full answer...

Replacement Bearings for Dexter 2,800 lb Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching