Can Progressive Dynamics Transfer Switch PD52 Be Installed In The Vertical Position?

Question

Question:

Can this switch be mounted horizontal vice vertical? Supply cables from shore and generator are too short to allow for vertical mount as in the pictures on webpage.

asked by: Donald R

0

Expert Reply:

I attached a section of the instructions which shows you should mount the Progressive Dynamics Transfer Switch - Metal Case - 50 Amp - 120V/240V # PD52 in the vertical position. It should not be installed in the horizontal position. If you need longer wire then I recommend looking on the attached link so you can match up some wire that is the same gauge you are currently using. You will likely use 10 gauge like 10 Gauge Primary Wire - Blue - per Foot # 10-1-1. You may need some connectors like Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5 # DW05745-5.

expert reply by: Andrew N

0

Progressive Dynamics Transfer Box Installation
(click to enlarge)

Answer 1

It is possible to use a 50 Amp transfer switch with a 30 amp setup since you plan on upgrading in the future however, the Furrion Transfer 50 Amp Switch is made for 50 Amp setups. I recommend to use Progressive Dynamics 50 Amp Transfer Switch part…

view full answer...

Answer 2

The Progressive Dynamics Transfer Switch - Metal Case - 50 Amp - 120V/240V #PD52 (Alternatively PD52V) and the PD52DCS/PD52DCSV are both part of the PD52 series but there are some differences. Both share the same voltage rating and current ratings.…

view full answer...

Answer 3

Yes, since the Progressive Dynamics Transfer Switch #PD52 is 120 and 240 volt compatible this will work fine with 30 amp as well as 50 amp. This 50 Amp transfer switch will allow you to hook up the 30 Amp shore power to the HOT 1 connection in the…

view full answer...

Answer 4

From the specs available to me, yes the Progressive Dynamics Transfer Switch, #PD52 is a good replacement option for the Todd Engineering TES-350.

view full answer...

Answer 5

Yes, the Progressive Dynamics Transfer Switch part #PD52 has an automatic design with 50 amp rating and it's made right here in the USA. We also offer the Go Power Automatic Transfer Switch part #34270278 which is an automatic switch with 50 amp…

view full answer...

Answer 6

Realistically you should be using a 50A transfer switch like the: -Progressive Dynamics Transfer Switch #PD52. As using a 30A transfer switch would leave one leg of your panel unhooked, which isn't ideal. However, with that being said you can use…

view full answer...

Answer 7

The white version of the Camco RV Vinyl Trim Insert - Black - 1000' Long x 1" Wide #CAM25312-10 that you were looking at is part #CAM25302. This roll is only 100ft in length though. Let me know if you need a different width or length and I…

view full answer...

Answer 8

The trims inserts are a universal fit so the key to finding the correct one for your 2019 Keystone Premier travel trailer is to measure the trim to determine what the proper width would be. The Camco RV Vinyl Trim Insert #CAM25312-10 you were looking…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Can Progressive Dynamics Transfer Switch PD52 Be Installed In The Vertical Position?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching