Adapters Needed For Female POL Fitting To Type-1 Fitting

Question

Question:

Is there something I could attach that would have a level gauge detector to the tank?

asked by: Myles A

1

Helpful Expert Reply:

To connect to the POL fitting on your 100lb tank you'll need the MB Sturgis Propane Hose # 100022-144-MBS which has a male POL fitting and the MB Sturgis Disposable Propane Bottle Adapter Fitting # 204132-MBS which will connect to the 1"-20 fitting on the hose and to your green Type-1 fitting on your RV.

expert reply by: Kevin C

1

POL Fitting
(click to enlarge)

Type-1 Fitting
(click to enlarge)

Myles A.

8/23/2021

Is there something I could attach that would have a level gauge detector to the tank?

Reply

Kevin C.

8/23/2021

Yes, you can attach the Camco Propane Cylinder Gas Gauge and Leak Detector # CAM59023 between the Type-1 fitting and the # 204132-MBS. As the temperature cools, propane condenses and as the temperature rises, the propane will expand in the tank. As a result, your propane tank will provide different pressure readings depending upon the temperature of your tank, which may or may not match the actual amount of propane within the tank. This gauge has three indicators on it to give you an accurate gauge no matter the weather.

Reply

Answer 1

After some internet research, it seems that others have tried and failed to find that elusive part also. Save time and trouble = replace both parts with the Camco #CAM59853 Quick Connect Kit. When making threaded propane connections, apply JR…

view full answer...

Answer 2

The Camco RV Portable Propane Campfire #CAM58041 has a built-in regulator so it can connect directly to your RV's high-pressure propane feed. My contact at CAMCO confirmed this is the preferred installation method. It comes with an 8 foot…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I looked up the hose and the regulator you currently have, and found that the GHA7 hose uses an ACME Nut connector to the LP tank and a 1/4 inch male inverted flare that connects to the 3/8 to 1/4 adapter used on the regulator. We offer the necessary…

view full answer...

Answer 7

To determine if the Replacement Shock for Titan Model 6 and 10 Brake Actuators, part #T1242600 will work to replace your Gabriel number 610712 (T2032) shock, you will need to verify a few quick measurements. Part #T1242600 will work as a replacement…

view full answer...

Answer 8

The fan in the #PD4645V is temperature controlled so typically it does not run continuously. However, if there are heavy loads you can expect the fan to run non-stop. According to Progressive Dynamics, this can also happen if you're charging…

view full answer...

Adapters Needed For Female POL Fitting To Type-1 Fitting

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching