7-Way RV to 7-Way Dinghy Tow Bar Wiring Extension

Question

Question:

2016 Wrangler sport hooking up to a 2021 Fleetwood Bounder. I have the plug in female adapters on both vehicles so I don't need the wiring kit just the line with both male plugs. Do you sell these?? Thanks in advance.

asked by: Marc D

0

Expert Reply:

Thanks so much for the photos they were super helpful, and what you have is a 7-way on the RV and 7-way on your Jeep, and we do have one option for an extension cord that will work for you:

- Curt Tow Bar Extension Cord w/ Socket - Coiled - 7-Way RV - 96" Cord # C39HR

This cord will stretch up to 8 feet long which will easily span the width between your connectors. It does come with the additional 7-way socket for your Jeep which you don't need, but since 7-way to 7-way tow bar wiring is pretty rare, this is the only option for an extension. Still, it certainly doesn't hurt to have a spare on hand as an eventual replacement if needed.

expert reply by: Kyle S

0

RV-Side 7-Way
(click to enlarge)

Jeep-Side 7-Way
(click to enlarge)

Answer 1

If your trailer has a female connection point then you'll want to use the Curt Tow Bar Extension Cord w/ Socket - Coiled - 7-Way RV to 6-Way Round - 96" Cord #C59HR. If your trailer has a cable with a male 6-pin connector then…

view full answer...

Answer 2

There are a number of options for routing the hot lead to the battery when installing the T-One Vehicle Wiring Harness #118767 in your 2015 Honda Fit, but since this harness mounts outside the vehicle the best option is to run it along the exterior…

view full answer...

Answer 3

Yes, you can utilize the unused 12v pin on your 7 way and 6 way plug in order to keep your towed vehicle's battery topped off. Keep in mind, this will only act as a battery maintainer / tender but it will not charge a completely dead battery.…

view full answer...

Answer 4

You link to #C59HR, the Curt Tow Bar Extension Cord w/ Socket. This connects the 7-way, blade-style connector from an RV to the 6-way round connector used for towed vehicles. This drops the black wire, the battery hot lead.

view full answer...

Answer 5

You can certainly add a 7-way trailer connector to your trailer with 6 wires. You would simply have 1 pin on the 7-way connector that did not function. I recommend adding a 7-way molded trailer wire connector like part #H20046, and a junction box…

view full answer...

Answer 6

I do believe you are looking for the Curt Mounting Bracket for 7-Way Connector Plug #C67UR. Or the Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long #C57202. These will let you connect and hold any loose wire…

view full answer...

Answer 7

Yes, you should be able to set up your Jeep Gladiator same/similar as Wrangler. Are you using the same supplemental braking system you had on previous towed Jeep? Was your previous Wrangler set up with something such as the Towed Vehicle Battery…

view full answer...

Answer 8

What is most likely going on is that your charge wire circuit is just not able to provide enough of a charge for the battery. It's a pretty long distance from the front of the motorhome to the back and then from there to the toad battery and the…

view full answer...

Answer 9

You could use the Demco Towed Vehicle Battery Charge Kit part #DM66VR on your 2013 Jeep Wrangler regardless of what flat towing setup you have since it's design is universal.

view full answer...

Answer 10

The correct way to wire up the breaker that comes with the Roadmaster charge line kit part #RM-156-25 is to have the copper post ran to the positive post of the battery that is charging the other vehicle and the silver side to the battery that is…

view full answer...

Answer 11

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Answer 12

To get a 7-way for your 2020 Jeep Wrangler 2 door, you will start with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118786 and then add the Adapter kit #ETBC7. The 4-way wiring will connect to your factory wiring, and then the…

view full answer...

7-Way RV to 7-Way Dinghy Tow Bar Wiring Extension

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching