Will Ark Extreme Off-Road Jack ORJW750BD Fit 2" x 2" Trailer Frame?

Question

Question:

Hello, Will this jack fit on to a 2inch x 2inch frame? I see 3inch - 6inch tall and 3inch wide, so want to be sure it would fit for my use a seeder with a smaller 2inch x 2inch frame where it would mount.

asked by: Franklin

0

Expert Reply:

I reached out to my contact at Ark and he was able to confirm that the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels # ORJW750BD you were looking at will work just fine on your seeder with a 2" x 2" frame.

This jack offers up to 10" of lift, and has a 1650lb capacity with dual wheels with rubber tires to allow you to easily move your seeder around when it is unhooked from your tow vehicle.

I included a video of the # ORJW750BD for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Here is an image I have from the Xtreme Off-Road Swing-Up Trailer Jack #ORJW750D in zinc which will have the same dimensions as the black Jack #ORJW750BD you are looking at.

view full answer...

Answer 2

To make sure the Ark Extreme Off-Road Swing-Up Trailer Jack #ORJW750BD will fit your trailer, there will be two things that need to be confirmed. First will be the tongue weight of the trailer you want to attach it to. This has a static, or resting,…

view full answer...

Answer 3

When folded up and traveling the Xtreme Off-Road Ratcheting Trailer Jack item #ORJW750BD is 29" long from the top of the jack to the bottom of the wheels. From the bottom of the wheel to the center pivot point where the bracket attaches is…

view full answer...

Answer 4

The diameter of the pull pin that holds the #ARK47FR jack in place on the mounting bracket is .5512".

view full answer...

Answer 5

I spoke with Ark and they told me that the Extreme Off-Road Ratcheting Trailer Jack w/ Dual Wheels #ARK54FR stick out 9-1/2 inches from the trailer frame it attaches to.

view full answer...

Answer 6

The Extreme Off-Road Swing-Up Trailer Jack part #ORJW750BD will fit any trailer with a tongue ranging from 3" to 6" tall. The width does not matter as longer bolts can always be used to accommodate different needs. That said, I don't…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Will Ark Extreme Off-Road Jack ORJW750BD Fit 2" x 2" Trailer Frame?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching