Can Legs of Lippert Ground Control be Replaced with Shorter Versions

Question

Question:

My 5th wheel came with Lippert Jacks 305339/344792 rear leveling jacks, but they hang lower than I’d like and have, in fact impacted curbs. Can I install instead 342610/428493 left/right to gain 2+ Inches ground clearance? Is there anything I need to worry about wrt the control system?

asked by: Jeff B

0

Expert Reply:

If you have the longer Lippert Ground Control jack legs you can convert them to the shorter ones like the part # LC342610 for the left side and # LC428493 for the right side.

expert reply by: Jameson C

0

Answer 1

If you have the Lippert Ground Control 3.0 then your middle jack is either the 17" Tall #LC342610 or the 19" Tall #LC305339. I'm not sure where you would be able to find a part number but if you check out the attached photo…

view full answer...

Answer 2

Lippert does sell the motor separately but unfortunately not the leg unit. If you are needing the leg unit then you will need to purchase the entire rear jack. Thank you for the picture and your description. Between the Replacement #LC305339 and…

view full answer...

Answer 3

The Replacement Left Rear Leg for Lippert Components Ground Control 3.0 Electric Leveling System - Qty 1 #LC305339 has the following dimensions: 9 inch diameter foot plate 23-1/2 inches tall without foot plate 8-1/2 inches wide at widest point…

view full answer...

Answer 4

Thank you for the picture with the measurement of your current Lippert Ground Control right rear leg that measures 24-1/2 inches from top to bottom when retracted. Based on that the correct replacement is the part #LC344792 and not the one you…

view full answer...

Answer 5

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Can Legs of Lippert Ground Control be Replaced with Shorter Versions

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching