Malone Bed Extender Width Capacity

Question

Question:

Will 4’ wide plywood fit on this

asked by: Richard

0

Expert Reply:

The Malone Axis Truck Bed and Roof Load Extender for 2" Hitches - 375lbs Item # MPG907 has load stops that can adjust from 28" to 48" so you'll have a very snug fit hauling your 4' wide plywood.

expert reply by: Kevin C

0

Answer 1

The longest option is going to be the Malone Axis Truck Bed and Roof Load Extender for 2" Hitches #MPG907, which has a 53" length from the hitch pin hole to the furthest point on the extender. This extender comes with a 375lb load…

view full answer...

Answer 2

The Erickson Big Bed Load Extender #EM07600 has crossbars which are 48-1/2" when in use, and that dimension does not include the wings - or tie-down points - at the end of the crossbars. The 48-1/2" is usable space, so your…

view full answer...

Answer 3

I confirmed with Erickson that the Erickson Big Bed Junior Load Extender #EM07605 has usable space (between hooks) of exactly 48" as you can see in the attached photo. Your plywood could possibly fit, but you may have trouble fitting it…

view full answer...

Answer 4

Since your 2022 Toyota Tacoma has a smaller bed and you're wanting to carry a longer canoe I encourage you to use a 2-bar roof rack system. For this I recommend the Rhino-Rack Vortex system which includes the following: 54" Vortex Crossbars…

view full answer...

Answer 5

According to my Erickson representative, their Big Bed Load Extender, part #EM07600 is 48-3/4 inches long, measured from the hitch pin hole to the rear surface of the upright, as shown in the provided photo. If you click the provided link, you can…

view full answer...

Answer 6

The Big Bed load extender, part #EM07600, has three height settings in 1 inch increments. I went out to the warehouse and measured from the center of the hitch pin hole myself and they're about 17-1/8, 18/-1/8, and 19-1/8 inches to the top of the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Malone Bed Extender Width Capacity

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching