What are the Bolt-Hole Dimensions of the Flex-a-Lite 14 Radiator Fan?

Question

Question:

Can you tell me what the mounting bolt hole diameter is on this fan?

asked by: Jeff C

0

Expert Reply:

I confirmed with Flex-a-Lite that the bolt hole dimensions on the Flex-a-lite 14" Trimline Reversible Electric Radiator Fan - 12V - 1,585 CFM # FLX114 are 6mm in diameter. I went ahead and attached a picture to this answer to give you perspective.

expert reply by: Bob C

0

Flex-a-lite 14" Trimline Reversible Electric Radiator Fan - 12V - 1,585 CFM # FLX114 Bolt-Hole Diameter
(click to enlarge)

Answer 1

The recommended thermostat switch for the Flex-a-lite 16" Flex-Wave Electric Fan part #FLX236 in the 1999 Ford F-250 4x4 is Flex-a-lite Adjustable Temperature Controller for Electric Fan part #FLX31149 which will actually read the engine…

view full answer...

Answer 2

If there is a fan clutch between the fan and radiator on your vehicle, then you will be able to turn the fan by hand when the engine is off and not running. If there is no clutch, the fan would be difficult to turn because you would have to turn…

view full answer...

Answer 3

Orientation of the inlet and outlet ports does not matter, and it does not matter which line goes where. Your best bet is to figure out the best mounting situation for the easiest connection to your vehicles transmission fluid return line. If you…

view full answer...

Answer 4

The Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class II - Efficient #D13501 is the most popular universal-fit transmission cooler for various vehicles and should fit your 2019 Toyota RAV4. This cooler measure 11" wide,…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

What are the Bolt-Hole Dimensions of the Flex-a-Lite 14 Radiator Fan?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching