Parts Needed to Install Brake Controller on 2013 Toyota Tundra with Factory Tow Package

Question

Question:

What accessories harnesses, brackets, etc. will I need to order with a Curt Triflex for a 2013 Tundra TSS? It has a factory tow package with 4 and 7 pin connectors.

asked by: Eric D

0

Expert Reply:

The only thing you'll need to install the Curt # C24VV TriFlex brake controller on your 2013 Toyota Tundra is the # C51362 vehicle-specific brake controller wiring harness. As long as the vehicle is equipped with the factory tow package, you won't need anything else. The TriFlex controller includes the necessary bracketry and hardware for installation.

The factory tow package connector that the harness plugs into is located to the left of the e-brake pedal, above the kick panel as shown in the linked installation video.

expert reply by: Mike L

0

Answer 1

The Curt TriFlex #C24VV is a proportional brake controller with an internal sensor to help it know how much braking force to apply to your trailer. Since you are testing the 7-Way while sitting still in your 2008 Toyota Tundra the controller senses…

view full answer...

Answer 2

Brake controllers are not vehicle specific. A wide variety of brake controllers will work for your 2013 Toyota Tundra. If you have a factory 7-way, then there are vehicle specific wiring harnesses to make installation easier. You can find those using…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Parts Needed to Install Brake Controller on 2013 Toyota Tundra with Factory Tow Package

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching