Determining Which Idler Hub Assemblies Will Replace Hub and Drum Assemblies On 19' Boat Trailer
Question:
Hi, I am removing the brake drum assembly from my 19 foot boat trailer and want to install a standard hub kit. How do I figure out what my axle is rated for and what the taper is so i get the right part?
asked by: Pat R
Expert Reply:
I would be happy to help!
What you will need to do is go ahead and remove on of the hub assemblies from your 18' boat trailer and look for the bearing number stamped in the face of each the inner and outer bearings as shown in the included picture of the # L44649.
If the bearings on your trailer are worn to the point that you cannot read the bearing numbers you will need to use digital calipers # PTW80157 to preciesly measure your spindles in the locations shown in the included diagram.
If you can provide the above information I would be happy to recommend the correct idler hub assembly for you.
Lastly keep in mind that depending on the weight of your trailer when it is loaded with your boat, you may legally be required to keep brakes. I recommend checking with your local DOT to make sure you will not run into legal issue by remove the trailer brakes.
Products Referenced in This Question
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Product Page this Question was Asked From
CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Pre-Greased
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- CE Smith
more information >
Continue Researching
- Shop: Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber
- Shop: Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: ONE LED Trailer Tail Light - 6 Function - Submersible - 6 Diodes - Red Lens - Driver Side
- Shop: Optronics LED Combination Trailer Tail Lights - Submersible - 40 Diodes - Driver and Passenger Side
- Shop: LED Tail Light for Trailers Over 80" Wide - 8 Function - Submersible - 23 Diodes - Driver Side
- Shop: Optronics Trailer Clearance and Side Marker Light - Submersible - Rectangle - Amber Lens
- Video: etrailer Trailer Idler Hub Assembly Installation
- Search Results: mr26zr
- Search Results: lunette ring
- Video: Hopkins VueSMART RV and Trailer Backup Camera Review
- Video: Master Lock Hitch Locks - Standard Pin Lock - 3794DAT Review 3794DAT
- Search Results: k23~465
- Search Results: 23~465
- Search Results: oil cap wrench
- Search Results: hitch pin
- Search Results: ratchet binder
- Shop: Roof Rack
- Shop: Windshield Wiper Blades
- Video: etrailer Trailer Idler Hub Assembly Review
- Shop: Tonneau Cover
- Q&A: What Type of Grease is Recommended with CE Smith Trailer Idler Hub Assembly # CE13515
- Q&A: What Hub do You Recommend for My 2005 Karavan BW-2350-74-ST Boat Trailer?
- Shop: Trailer Hitch
- Q&A: Wet Bolt Suspension Upgrade Kit For 2005 Weekend Warrion 5TH Wheel Triple Axle Trailer
- Q&A: Gear Kit for Ram 8000 Series Trailer Jack
- Video: TryRyde Tang Type Replacement Spindle Washer Review
- Shop: Trailer Wiring
- Video: Review of CE Smith Trailer Hubs and Drums - Idler Hub - CE13515
- Article: How to Accurately Measure Trailer Leaf Springs