How To Find Correct Replacement Hydraulic Brakes for a ShoreLandr Boat Trailer

Question

Question:

Hi folks, Can you let me know if this product fits my double axel Shorelandr trailer Model 50TCBBLW. Thank you!

asked by: Antony P

1

Helpful Expert Reply:

In order to confirm the correct replacement braking assemblies for a trailer you'll need to find the axle capacity. The axle capacity can be found on the axle tag in the center of the beam. The Hydraulic Trailer Brake Kit part # AKUBRK-7 is designed for 5,200 lb - 7,000 lb axles. The other common axle capacity is 3,500 lbs and in which case you'd need the part # AKFBBRK-35.

expert reply by: Conner L

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 7

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 8

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...