How does the RED4FR Proportional Brake Controller Connect to a 2011 Ford Ranger?

Question

Question:

2011 Ford Ranger 4x4. I have always used BrakeSmart Brake controller, 2001 7.3 Super Duty which functions off of the trucks master cylinder, the more pressure from the break peddle equals more trailer breaks and the same with backing up, no magnet bite so how does the RED4FR work? Im pulling out my Tuson Break Controller because it has caused to many problems connecting into the trucks data port and everything I have tried has caused problems with Countys IM testing etc.. Whats so great? How does the RED4 now how to connect to the truck without wiring?

asked by: Brent C

1

Helpful Expert Reply:

The Redarc Tow-Pro Elite proportional trailer brake controller item # RED44FR is connected directly to your 2011 Ford Ranger 4x4 through a wiring harness. This harness comes with the brake controller and connects behind the dash by wiring into your truck. The Redarc brake controller activates trailer brakes in proportion to your vehicle's braking action by automatically adjusting your trailer's braking based on deceleration of your Ranger. The brakes also activate immediately which eliminates pausing like with time-delayed brake controllers. This brake controller has one of the most subtle footprints for vehicle installed controllers. The main unit installs out of sight and the control knob mounts in the dash or another easily accessible area. I have linked an installation and review video.

expert reply by: Jerred H

1

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 3

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

The #37213635 JR Products Replacement Landing Gear Switch you'd mentioned would be a proper replacement for your existing Atwood 70254 landing gear switch. If you wanted the switch, wiring harness and the bezel for the switch, use the Stromberg…

view full answer...

Answer 6

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Sounds like you've done a great job at installing the Redarc Tow-Pro Elite #RED44FR, and that you're on the right track when it comes to installing the Hopkins Endurance Multi-Tow Plug #HM47180 on your 2019 Ford Ranger! To wrap up your…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

When it comes to installing The Timbren Rear Suspension Enhancement System #TFRRGR on your 2020 Ford Ranger they come in a pair. The Timbren springs has a 6,000 pound weight capacity, and no drilling is required during the installation. I attached an…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

How does the RED4FR Proportional Brake Controller Connect to a 2011 Ford Ranger?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching