Recommended Camper Tie-Downs For A 2010 Toyota Tundra Short Bed

Question

Question:

Hello is there a specific reason why this kit won’t fit the short bed tundra?

asked by: Oscar

0

Expert Reply:

The HappiJac Truck-Mounted Camper Tie-Downs Item # LC184089 is not a confirmed fit for your 2010 Toyota Tundra because the frame is different and bends in the plates are different on the 5-1/2' beds versus the 6-1/2' and 8' beds.

The TorkLift Custom Frame-Mounted Camper Tie-Downs - Front # TLT2307 and TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear # TLT3304 are a confirmed fit for a 2010 Toyota Tundra 5-1/2' bed.

You'll also need some turnbuckles to lock down your camper. I recommend the TorkLift Locking FastGun Turnbuckles for Frame-Mounted Tie-Downs - Stainless Steel - Black - Qty 4 Item # TLS9529-2-LK. The quick-release levers on these turnbuckles make it fast and easy to secure your truck bed camper to your vehicle.

expert reply by: Kevin C

0

Answer 1

The best and most secure camper tie down system that fits your 2016 Toyota Tundra 6.5 foot bed double cab is by far the Happijac system part #LC184089. This kit attaches to the truck frame instead of to the bed which provides a much stronger and more…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Recommended Camper Tie-Downs For A 2010 Toyota Tundra Short Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching