Front Hitch Weight Capacity for a 2019 Jeep Wrangler

Question

Question:

What is the weight capacity for the front hitch?

asked by: Richard

1

Helpful Expert Reply:

The vertical load limit for the Curt front hitch that fits your 2018 Jeep Wrangler item # C31433 is 525 lbs. The vertical load rating for a front mounted hitch is the same thing as tongue weight rating for a rear trailer hitch. I've included a couple pictures of the hitch installed.

expert reply by: Jerred H

1

Jeep Wrangler Front Hitch mount photo 2019
(click to enlarge)

Jeep Wrangler Front mount hitch
(click to enlarge)

Answer 1

The Curt Front Mount Trailer Hitch Receiver item #31433 you referenced is for the 75th Anniversary Edition Jeep Wrangler that came out in 2016 it also fits the hard rock editions. These models have the hard rock bumper which changed the mounting…

view full answer...

Answer 2

To answer your question about which front mounted hitch option you should order for your 2016 Jeep Grand Cherokee, there is actually only one that fits, the Curt Front Mount Trailer Hitch Receiver #C31033. That said, your tow hooks do need to be…

view full answer...

Answer 3

Curt front mount trailer hitch #C31033 will fit your 2013 Jeep Grand Cherokee as long as the vehicle does not have factory tow hooks. There are no options if it does have factory tow hooks. Though we have heard of at least one customer who had a…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

The B and W Companion hitch part #BWRVK3370 that you referenced does not come assembled. The head will come in one box, and the slider setup will be separated out into two more boxes. I attached a link to the install instructions for you to check out…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 12

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Front Hitch Weight Capacity for a 2019 Jeep Wrangler

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching