How To Determine Fit of CE Smith Post-Style Guide-Ons for Boat Trailers

Question

Question:

i need a trailer guide that will fit my trailer that has a step at the rear of trailer the boat is 19 foot.

asked by: Fred B

1

Helpful Expert Reply:

The CE Smith Post-Style Guide-Ons for Boat Trailers part # CE27648 are universal fit boat guide-on designed for I-beam trailer frames up to 4" wide. The closer to the rear they are installed, the more they will assist with loading. That said, you can install them further forward if there is something on the frame mounted in the way. In regards to universal fit items, compatibility will be up to the installer.

expert reply by: Conner L

1

Answer 1

I have a solution for you, but unfortunately those 7ft long bunk boards #CE27845 are going to be the longest ones we currently offer. If you wanted to source the wood yourself you could then just use some marine grade carpeting like the CE Smith…

view full answer...

Answer 2

Choosing the correct guides is a little different for each boat/trailer combo but we do have a few options that you can choose from. I recommend going with either the CE Smith Bunk-Style Guide-On Kit #CE27600K90 where you supply your own 2x4 boards…

view full answer...

Answer 3

The #CE27648 Guide Ons you'd looked at are designed for I-beam trailer frame members, from the photo you provided, it looks like your frame members are a simple boxed in rectangular tube. If that's the case, and the frame members aren't…

view full answer...

Answer 4

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 5

I've had to do this before, so I understand your concern about the carpet getting shredded. What I did was take a sharp utility knife and cut a small X right where I wanted to drill my holes. This worked very well and didn't rip up the…

view full answer...

Answer 6

I was able to track down some measurements for the 90 degree uprights that are included with the #CE27600K90 bunk kit. Hope this helps. See below: A: Internal Distance - 15-1/2" A: External Distance - 17" B: Internal Distance - 18" B:…

view full answer...

Answer 7

The CE Smith bunk boards, part #CE27845, are made from untreated southern yellow pine 2 x 4's.

view full answer...

Answer 8

Provided that the widest part of the I-Beam frame is no wider than 3 inches and the overall height no more than 4-1/4 inches you could use CE Smith Bunk-Style Guide-Ons #CE27600 with the I-Beam frame. The fact that the frame is aluminum should not be…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

How To Determine Fit of CE Smith Post-Style Guide-Ons for Boat Trailers

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching