Replacement For A Magnatek Model 80 Power Converter

Question

Question:

I believe I toasted the circuit board, as 240v were sent to it and not 120v. Now nothing works, electrically. Can I replace just the board??

asked by: Stephen

0

Expert Reply:

We don't offer the circuit boards for Magnetek power converters but I do recommend a complete replacement as more than just the circuit board could've been damaged. I recommend the Progressive Dynamics Inteli-Power RV Converter and Battery Charger - 12V - 30 Amps Item # PD9130. The # PD9103 will convert AC shore power to DC power to quickly charge your RV batteries and provide continuous power to your DC breaker panel to run 12V loads. It works with flooded lead acid, AGM, and gel batteries.

You'll want to double check the amperage of your old converter to ensure this is the correct amperage unit to match. If not, please reply back with the amperage of your old unit and I can find the correct replacement for you.

expert reply by: Kevin C

0

Answer 1

The Model 80 refers to the ac/dc distribution panel not the converter but what this does tell me is that you have a standalone converter. Therefore, if the converter is indeed 30 amps then the Progressive Dynamics Inteli-Power RV Converter and…

view full answer...

Answer 2

If this is a standalone unit and you just need a new converter then you can use the Progressive Dynamics Inteli-Power RV Converter and Battery Charger part #PD9130 as a replacement. If you are instead looking to upgrade the entire panel then I…

view full answer...

Answer 3

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 4

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 8

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

I spoke with Lippert and they said the Kwikee 35 Series Electric RV 1-Step part #LC3691461 will be a direct replacement for the Coach Steps 725-0041. It will be a bolt-on install for the most part for the exception of changing out the door switch…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

I spoke with my contact at Progressive Dynamics and they informed me that the Lithium Converter for WFCO RV Power Centers part #PD4655LIV does work as an upgrade for the Parallax 7355. It has the same housing as the Replacement Converter for…

view full answer...

Replacement For A Magnatek Model 80 Power Converter

Featured Help Information

Miscellaneous Media

Continue Researching