Holes for the Valterra RV Water Tank

Question

Question:

Hi I bought the Valterra RV Water Tank and the fittings. If I want to install the the 1/4inch 90-Degree barbed elbow on the tank for inflow, where should I install? 1 On the sides that already have the holes or 2 on the body that has no holes? Please see the photo attached. Thanks

asked by: Mauricio C

0

Expert Reply:

If for positioning/location of the Valterra RV Water Tank, # R8024, you need to create a new hole location then do so. However, if for your application you can select one of the fitting locations that is not yet drilled through, I suggest using that location as it has more structure.

expert reply by: Michael R

0

Answer 1

I contacted the vendor and the Valterra RV Water Tank - Non-Toxic - ABS Plastic - 24" x 8" x 16" - 12 Gallons #R8024 does not have any specific pressure rating since it is designed to be gravity fed or used with…

view full answer...

Answer 2

Valterra ABS water tanks like the #R8024 are baffled every 18" for surge control and made from lightweight ABS plastic, so they're just not designed to handle to additional pressure that is created from an electric water pump sucking…

view full answer...

Answer 3

The adjustment holes on the Super Titan Forged Pintle Hook Plate part #RP38186 are 17/32" diameter so they will accept and are designed to be used with 1/2" bolts. It should not matter what brand pintle hook is used as the hole size…

view full answer...

Answer 4

The Pintle Hook #C48215 that you referenced does include mounting hardware to attach to a pintle hook plate like the Super Titan Forged Pintle Hook Plate #RP38186 that you referenced. I also pulled these two parts and was able to determine that…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

The best option for a Class C motorhome windsheild cover is going to be the Adco Deluxe Cover part #290-2507 which is designed for Class C motorhomes just like yours. I attached a review video for this cover for you to check out as well.

view full answer...

Answer 7

The Kodiak Oil Cap #KPCAP you are looking at is a replacement cap for the Kodiak Pro Lube Kit. The oil cap you need is the Redline Oil Cap, Plug and O-Ring for Dexter 7-9K Trailer Axles #RG04-230. This will replace the oil cap on your trailer axles…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 10

I recommend replacing an entire ladder if it's damaged. You'll want to find a replacement based on the height. Such as the Stromberg Carlson #LA-401 that is 99-1/2 inches tall. They can be cut shorter to customize the length if needed.

view full answer...

Answer 11

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Holes for the Valterra RV Water Tank

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching