What Is the Finish Like On the RC Manufacturing T-Series Trailer Tongue Tool Box

Question

Question:

Is the finish smooth black or granite?

asked by: Mark W

1

Helpful Expert Reply:

The RC Manufacturing T-Series Trailer Tongue Tool Box part # 350980 has a black powder coated finish. Powder coated finishes are usually not as smooth as painted finishes. They are however much more durable than paint. If the tool box was painted it would chip easily and reveal the metal underneath which would eventually rust.

expert reply by: Conner L

1

Answer 1

The closest match we have to the dimensions you are looking for in an A-Frame toolbox is going to be #350980. It measures 30 inches across at the back, 17-1/2 across at the front, 14 inches front to back, and 14 inches tall. Everything else is going…

view full answer...

Answer 2

There isn't one set in stone way to install the RC Manufacturing T-Series Trailer Tongue Toolbox #350980 but typically people will drill holes through the bottom of the box and into the trailer frame below it and then run carriage bolts through…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Waylon, it does look like the Dexstar Steel Mini Mod Trailer Wheel #AM20539 is the same thing as the Dexstar 17-233 wheels you're referring too. These are silver wheels with a 6 on 5 1/2 bolt pattern, a 0 offset, and are made in the USA.

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

What Is the Finish Like On the RC Manufacturing T-Series Trailer Tongue Tool Box

Product Page this Question was Asked From

Continue Researching