Replacement Hex Head Bolt for Gear on Lippert Coach Step

Question

Question:

I need a replacement bolt for the center bolt on the mail gear of a set of Coach Step brand RV steps Electric #164194, Three steps of 24inch x 11inch can you provide a parts list for this stair assembly? do you have the identified bolt for my steps?

asked by: Walt C

0

Expert Reply:

I was able to confirm with my contact over at Lippert that the hex head bolt you're looking for is available with part # LC77UD. This is the bolt that goes through the main gear of your Lippert Coach Steps.

expert reply by: Erik B

0

Answer 1

I checked with Lippert for help on this and they sent me the attached install instructions for you to check out that cover removing the bolt. Basically there will be Loc-Tite so heat is required but in some cases there is a tack weld that will need…

view full answer...

Answer 2

Thank you for the picture of the bolt you need, based on that the correct part is the #LC128969 that you referenced. We have checked in the past and removal of the step assembly is required. See attached picture.

view full answer...

Answer 3

The large center bolt which holds the gear to the steps on a set of Coach steps is the Replacement Socket Head Cap Screw for RV Coach Steps part #LC128969.

view full answer...

Answer 4

The Replacement Control Module for Lippert Electric Coach Step #LC301702 has the purple wire that connects to the door light switch. The other end of the switch #LC301694 connects to the Replacement Wiring Harness for Lippert Electric Coach Step…

view full answer...

Answer 5

I believe the part that you are looking for is included in the Replacement Joint Assembly Hardware Kit #LC216567. This includes that large black bolt that is on your Lippert Gear #LC301696.

view full answer...

Answer 6

The correct replacement control module for the obsolete Lippert Coach Step 128980 double retractable step kit is part #LC301702, according to the nice folks at Lippert. If you click the provided link, you can see a video product description of the…

view full answer...

Answer 7

Sounds like you have a system like the Voyager RV Observation Camera System w/ Monitor and Mount #VOM43HDCL1B. I attached our review video of this system which explains the different features, wiring harnesses, and shows how the system looks…

view full answer...

Answer 8

Lippert no longer offers the individual steps as a replacement part, but the motor is available as part #LC301695 and the control module is part #LC301702, If the step in question was bent, it might be possible to straighten it, as the steps, slide…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Replacement Hex Head Bolt for Gear on Lippert Coach Step

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching