What is the Weight of the Trailer Hitch e65ZR for a 2021 Subaru Outback Wagon

Question

Question:

Hi, I plan on installing this hitch myself on a 2021 Subaru outback and wanted to know the weight of the hitch. Thanks

asked by: Mr. C

0

Expert Reply:

The Curt # C67JR weighs 31 lbs, so it's not impossible to manage on your own with some jack stands or some other manner of propping the jack up while you bolt it into place.

I have linked the written instructions for you to take a look at.

expert reply by: Erik B

0

Answer 1

I can tell you how to determine the approximate amount of ground clearance you'll have with the Curt Trailer Hitch Receiver #C67JR installed on your 2020 Subaru Outback, though as of this writing (January 2020) we have not been able to test fit…

view full answer...

Answer 2

To install the Curt hitch part #C67JR on your 2020 Subaru Outback Wagon you will not have to lower the exhaust.

view full answer...

Answer 3

In order to install a trailer hitch on a 2020 Subaru Outback you will need to trim the rear lower bumper fascia but this is unavoidable and very minor because it cannot be seen from the outside of the vehicle. The amount of cutting will vary…

view full answer...

Answer 4

I am happy to confirm that the Curt Trailer Hitch Receiver #C67JR you were looking at is confirmed to fit all models of the 2022 Subaru Outback Wagon so it will fit your 2022 Subaru Outback Wagon Wilderness even though it uses a slightly different…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

What is the Weight of the Trailer Hitch e65ZR for a 2021 Subaru Outback Wagon

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching