Can MORryde Power Cord Storage System be Used on Hardwired

Question

Question:

Whats the solution for a hard wired set up?

asked by: Larry C

0

Expert Reply:

If you wanted to use a Power Cord Storage system like the part # MR77RR on a hardwired setup you'd have to use it a little differently and it may not be as convenient. You'd have to put the end of the cable in the reel and then roll up it up "backwards" basically from there. So to use it you'd have to unroll it completely off the reel and then grab the end of the cable and take it where it needs to go.

expert reply by: Jameson C

0

Answer 1

For a hardwired 50 amp cord like what you have you'd have to insert the free end of the cable into the MorRyde part #MR47RR and reel it in that way. If you wanted to change your setup to a detachable cord you certainly could so that you…

view full answer...

Answer 2

I spoke with my contact at Lippert about the Underchassis Double Bin Storage Unit, part #LC236558. They told me that the mounting angle brackets are 1 inch wide. They gave me the distance from the end of the storage bin to the edge of the mounting…

view full answer...

Answer 3

The drawers on the Underchassis Double Bin Storage Unit #LC236558 just slide in the steel frame. It does not have rollers.

view full answer...

Answer 4

We have a storage reel for your 36 foot long power cord, but the MORryde Manual Storage Reel for 30' Long Power Cords #MR77RR will only fit power cords up to 30 feet long, which I verified with the manufacturer. Instead, for the length of your…

view full answer...

Answer 5

See the picture to the right for a wiring diagram of seven-way vehicle end trailer connector. If you click on it you can enlarge it. I have also included a trailer wiring FAQ page for you to check out.

view full answer...

Answer 6

Depending on how much clearance you have will determine what will work for you. The MORyde Manual Storage Reel #MR77RR is our smallest reel storage we offer, measuring in at 12-3/4" long, 14-15/16" wide, and 13-7/16" tall.

view full answer...

Answer 7

The MORryde Manual Storage Reel #MR47RR has a lot of parts that are involved in the handle assembly. I have added a picture to help see the order. First onto the machined drum piece you will slide 2 white plastic washers. Then there are 3 wave…

view full answer...

Answer 8

The mounting brackets of the Lend-A-Hand part #AM-533 that you referenced measure 2-5/16 inches wide x 3-7/8 inches in height.

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Can MORryde Power Cord Storage System be Used on Hardwired

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching