Trailer Wiring Harness Fit For 2021 Ford Bronco Sport

Question

Question:

What is the wiring harness for a bronco sport 2021 model that will fit

asked by: Larry S

0

Expert Reply:

We do have a trailer wiring harness that fits your 2021 Ford Bronco Sport, which is the following part:

- T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # TK46FR

This harness is manufactured by Tekonsha, who is known to make the most reliable trailer wiring harnesses in the industry, so it's going to provide you with the best way to power your trailer's lights. It does store in your Bronco Sport's rear cargo area when you aren't using it, so you don't need a mounting bracket.

If you also need a trailer hitch receiver for your 2021 Bronco Sport, the options are:

- Draw-Tite Max-Frame Trailer Hitch Receiver # DT93MR

- Curt Trailer Hitch Receiver # C76HR

Both have the same 3,500 lb towing, 525 lb tongue weight capacities, but I recommend going with the Curt as it's the easier install.

expert reply by: Kyle S

0

Answer 1

For the best hitch receiver for your 2021 Ford Bronco Sport, that is definitely the Curt Trailer Hitch Receiver - Custom Fit #C76HR. Not only is the Curt hitch assembled here in the U.S.A., it has an installation process that is much easier than the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Trailer Wiring Harness Fit For 2021 Ford Bronco Sport

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching