How Many Replacement Power Cords Do I Need For 2 Piece Thomas Payne Sofa

Question

Question:

Would one cord power both left and right seats or do I need two cords?

asked by: Amy S

0

Expert Reply:

You will only need one Replacement Power Cord with Power Supply Box for Thomas Payne Seismic RV Power Reclining Sofas # 195-000111 for your sofa as both sides are connected electrically during assembly.

expert reply by: Erik B

0

Answer 1

We offer a range of 2-step electric step assemblies for motorhomes like your 1986 Winnebago Chieftain 27 that are displayed on the linked page. These are available in three different widths: 24-inch, 26-1/4-inch and 30-inch. Based on photos of this…

view full answer...

Answer 2

Behind the Thomas Payne Seismic Recliners there are power connections on either end. These are located near the edges of the recliners near the bottom (see attached photo "C" connections). You'll simply push the Replacement Power Cord…

view full answer...

Answer 3

The Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas #LC36FR is the correct part for your Thomas Payne Seismic Series Recliner. If you have not already, preform a hard reset on your chair before continuing. To do this unplug…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

How Many Replacement Power Cords Do I Need For 2 Piece Thomas Payne Sofa

Product Page this Question was Asked From

Continue Researching