Does Reese Weight Distribution Shank Fit Equal-i-zer Weight Distribution

Question

Question:

Will this Reese hitch fit an Equalizer sway control hitch? Part # 09-00-1000

asked by: Ronnie M

0

Expert Reply:

It sure does; weight distribution shanks are by and large universal, so long as they have the correct bolt hole diameter of 3/4" and spacing of 1-1/4", which the Reese shank you asked about does:

- Reese Weight Distribution Shank for 2" Hitches # RP69FR

Because it has the correct dimensions, it will absolutely work with your Equal-i-zer weight distribution hitch.

expert reply by: Kyle S

0

Answer 1

Yes the Reese weight distribution shank part #RP69FR is perfectly compatible with the Husky brand weight distribution systems.

view full answer...

Answer 2

We do not recommend mixing different brands of components within a system, whether it be a weight distribution hitch or a 5th wheel hitch set-up. While it may be possible to do so in some instances, since the different manufacturers will not have…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Does Reese Weight Distribution Shank Fit Equal-i-zer Weight Distribution

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching