Shroud For 7333-C8876 Coleman Mach 3 Air Conditioner

Question

Question:

97 Yellowstone Capri air conditioner cover broken ac model number is 7333c8864

asked by: Roger

0

Expert Reply:

We do have the correct AC cover, as what you have is an older Coleman Mach unit. So what you need is the following:

- MaxxAir TuffMaxx Replacement RV Air Conditioner Cover for Coleman-Mach RV Air Conditioners # MA00-325001

I have added a link below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Answer 1

For your 4900K model you will want the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents #MA10-20281K-1AF since your model isn't opening.

view full answer...

Answer 2

The correct Replacement Operator Mechanism for your model 4751KS MaxxAir MaxxFan is part #MA10-20281K-1AF. If your fan lid is unable to open even manually, then this is the part you need to replace. The other part you referenced, #MA10A04751KS would…

view full answer...

Answer 3

We do have the correct replacement shroud for a Coleman Mach 3 Air Conditioner, the MaxxAir TuffMaxx Replacement RV Air Conditioner Cover for Coleman-Mach RV Air Conditioners part #MA00-325001. I checked the mounting hole spacing on this shroud and…

view full answer...

Answer 4

Based on my research it looks like you have an older Coleman Mach AC unit that precedes the Mach 1, Mach 3, etc models. The current version of your particular AC is the Coleman Mach 3. With this in mind the MaxxAir TuffMaxx Replacement Shroud…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Shroud For 7333-C8876 Coleman Mach 3 Air Conditioner

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching