Measurements For Installing B&W BWGNRK1111 Turnover Ball Gooseneck Hitch on 2011 Ford F-350
Question:
I would like to check the measurements to setup a 5th wheel companion hitch BWRVK3500. My truck is a 2011 ford F350 Super duty with a 8 foot bed. Diesel It is a 4 door. This hitch is attached to a goose neck. Right now I have it at the lowest height and as far back as possible. Thanks
asked by: Michael E
Expert Reply:
The B&W Companion # BWRVK3500 which is height adjustable from 16-1/4 to 18-1/4 inches above the bed floor, would attach to your 2011 Ford F350 using the B&W Turnover Ball hitch, part # BWGNRK1111. The Turnover Ball hitch mounts to that the truck bed so that the hole for the gooseneck ball where the Companion would install is 46-1/8 inches forward of the rear edge of the truck bed (the bed, NOT the edge of the tailgate).
The Companion 5th wheel hitch pivot arms can be installed to set both the hitch height as well as the fore/aft positioning of where the king pin/hitch jaw connection would be, which is between 1 to 7 inches rearward of where the Companion's post mounts into the Turnover Ball Hitch, as outlined in the linked instructions or the product page which is also linked.
I'm not sure exactly which measurements you were needing, but I've ran through everything relevant above. If I've overlooked a measurement you were needing, just let me know.
If you'd also like to install a 7-way connector in the truck bed so you don't have to run the trailer connector cable up over the tailgate, you can do so using part # C56000.
I've also linked to install/demonstration videos for the parts mentioned above.
Products Referenced in This Question
B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Gooseneck Hitch
- Below the Bed
- Manual Ball Removal
- 7500 lbs TW
- 30000 lbs GTW
- Removable Ball - Stores in Hitch
- Wheel Well Release
- 2-5/16 Hitch Ball
- B and W
more information >
Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 10' Long
- Custom Fit Vehicle Wiring
- Fifth Wheel and Gooseneck Wiring
- 10 Feet Long
- Custom Fit
- 7 Round - Blade
- CURT
more information >
Product Page this Question was Asked From
B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter - Dual Jaw - 20,000 lbs
- Gooseneck and Fifth Wheel Adapters
- Adapts Truck
- Gooseneck Hitch to Fifth Wheel Trailer
- No Offset
- 20000 lbs GTW
- Connects to Gooseneck Hole
- Fixed Height
- Hitch Adapters
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: B&W Companion Gooseneck-to-5th-Wheel Trailer Hitch Adapter - Dual Jaw - 20,000 lbs
- Q&A: How to Determine if B&W Companion 5th Wheel Trailer Hitch # BWRVK3500 will Clear Truck Bed Tool Box
- Q&A: Does Truck with 6-1/2 ft bed Have to Use Slider Hitch for Turning Clearance with Fifth Wheel Hitch
- Q&A: How to Access Rear of Drive RV Stereo # 324-000138 Thats Already Installed
- Article: Gooseneck to 5th Wheel Adapters
- Q&A: Options for Adding Interior Lighting to Enclosed Cargo Trailer
- Q&A: How to Power Trailer Dome Light When Not Connected to Tow Vehicle
- Q&A: Recommended Dexter Suspension Kit 7753400
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Replacement Drum Assemblies for AL-KO 8490 Hubs
- Article: Adapters for Towing a 5th Wheel Trailer with a Gooseneck Hitch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Ram Trailer Tow Prep Package