Kwikee 909513 Replacement Module for RV Steps

Question

Question:

Prior answers about replacing 909513 allude to older models being incompatable. I have one from a 1996 motorhome where I need a new controller board. What is the correct part?

asked by: Bill H

0

Expert Reply:

The correct replacement control module for your Kwikee Steps with Control Module 909513 is the Lippert Components Kwikee Control Unit part # LC379606 which is also correct based on age.

expert reply by: Jameson C

0

Answer 1

The correct replacement control module for your Kwikee Steps with Control Module 909513 is the Lippert Components Kwikee Control Unit part #LC379606.

view full answer...

Answer 2

It appears your issue is that you installed the wrong module on your RV steps. Since your module currently says 909513 the correct replacement solution is the part #LC379606 instead. This would explain why your door switch setup is not working…

view full answer...

Answer 3

Yes, for the Switch Kit Magnet for Lippert Components Kwikee RV Electric Step part #LC375385 but in white you would want to use the Lippert Replacement Round Magnetic Door Switch for Kwikee RV Step part #LC378047 which is also normally closed (NC).

view full answer...

Answer 4

To replace the control module 909513 on your old Kwikee steps you'll need the Replacement Control Unit for Kwikee Electric RV Steps #LC379606. Due to the age of your original step my Lippert contact noted that in some cases older steps may…

view full answer...

Answer 5

I contacted the manufacturer, Lippert, for you in regards to a diagram of wiring the Replacement Control Unit for Kwikee Electric RV Steps #LC379606. I have attached for you below the diagram that they sent me.

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Kwikee 909513 Replacement Module for RV Steps

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching