Is Mounting Hardware of Rhino Rack Pioneer Platform RR42115BF Adjustable

Question

Question:

How much space is between the cross bar clamps of this part # roof rack? And are they adjustable for width between them. I am looking at putting it on a Landcruiser and the space between the side rails is about 43inch across. Worried that this may not fit.

asked by: Timothy J

0

Expert Reply:

The mounting hardware of the Rhino Rack Universal Pioneer Platform part # RR42115BF is adjustable and can install between basically any of the slats so it can accommodate a narrower side rail setup like you have.

expert reply by: Jameson C

0

Answer 1

I would go with the Classic Accessories Universal Fit Spare Tire Cover #052963753875. This is a high quality spare tire cover that will fit your 145/90/17 tire. I calculated the diameter of your tire and determined that it is 30.8 inches which would…

view full answer...

Answer 2

I do have an option for you to install the Rhino-Rack Pioneer Platform Roof Tray on a 2017 Audi Q7 but not the way you described as you can't mix and match parts nor is there a direct mount option. There is also a platform size restriction for…

view full answer...

Answer 3

There is an option to mount the Rhino-Rack Pioneer Platform rack to the crossbars on your 2016 Toyota Tundra, and you will simply need one of the following, depending on the size you want. - 48" Long x 38" Wide: Rhino-Rack Universal Pioneer…

view full answer...

Answer 4

It is a smart idea to check, and I did verify for you with Rhino-Rack that yes, the mounting brackets are included with the Rhino-Rack folding ladder: - Folding Ladder for Rhino-Rack Pioneer Platform Racks #RRRAFL I have added a photo as well that we…

view full answer...

Answer 5

I have a solution for you. I reached out to Rhino-Rack, and they could not confirm for sure that the mounting brackets of the Folding Ladder for Rhino-Rack Pioneer Platform Racks - Aluminum #RRRAFL-RUFLB will be able to fit the channels on your…

view full answer...

Answer 6

Yes! For a ladder mount on your Rhino-Rack Pioneer Platform like the #RR42115BF, you need the Rhino-Rack Folding Ladder Brackets for Pioneer Platform Rack #RRRUFLB. This bracket allows you to carry 1 of the Rhino-Rack Folding Ladders #RRRAFL. The…

view full answer...

Answer 7

I will answer the car wash question first. Rack manufacturers will say do not go through a car wash with a roof rack on your vehicle. Have I taken my vehicle with a roof rack through a car wash before, yes. It was brushless and my rack was fine…

view full answer...

Answer 8

view full answer...

Answer 9

I have a similar solution I can recommend for you, but we do not have a spare tire mount for the Curt Cargo Basket part #C18115 that you referenced. Instead you would need the Yakima cargo basket part #Y07070 with the spare tire carrier #Y07076.

view full answer...

Answer 10

There is not a locking device that comes with the Rhino-Rack Spare Tire Carrier #RSWH. That said, depending on if the wheel has any type of gap/hole/spoke in it you may be able to lock it to your carrier with a cable lock such as the etrailer 10'…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Is Mounting Hardware of Rhino Rack Pioneer Platform RR42115BF Adjustable

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching