LED Trailer Taillights with 2 inch Between Mounting Holes and 2 Wire Design
Question:
My 16 ft low boy utility trailer has a cracked brake/turn signal/running light. It has 2 wires on the rear turn/ brake light. All I see are 3 wire set up when I try to order.The light mount is a 2” double bolt plate. What do you have in an led that would match up to what I’m trying to replace? Please send links. Also, it looks like they used whatever color wire they had so nothing is the same color on either side. How do I tell which wire to connect to what? I have a good voltage meter, so... Thanks,
asked by: Cody D
Expert Reply:
For a 2-wire trailer taillight with 2 inches between the mounting studs and is also LED you'd want the part # STL8RGB for the passenger side and part # STL9RGB for the driver side.
The two wires you have to your current taillights will carry the running light circuit on one wire and the stop/turn on the other. So you'd need to use your circuit tester to test both wire by function when connected to a tow vehicle.
Products Referenced in This Question
Combination LED Trailer Tail Light - Submersible - 7 Function - 14 Diodes - Driver Side
- Trailer Lights
- Tail Lights
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Square
- Pedestal Mount
- Submersible Lights
- LED Light
- 5L x 4-1/2W Inch
- Red
- Optronics
more information >
Product Page this Question was Asked From
Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Trailer Lights
- Tail Lights
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Square
- Pedestal Mount
- Submersible Lights
- LED Light
- 5L x 4-1/2W Inch
- Red
- Optronics
more information >
Continue Researching
- Search Results: trailer wire
- Video: Optronics LED Amber Clearance and Side Marker Light Review
- Video: Spectro Wiring SWC502905-1 Review
- Video: Review of Spectro Wiring - SWC502885-1
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Shop: Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
- Q&A: Wire Gauge Used on Optronics MCL95AB LED Clearance/Marker Lamp
- Q&A: How Long is the Power Wire Attached to the # MCL95AB LED Clearance Light
- Search Results: heat shrink
- Search Results: wire connectors
- Search Results: quick splice
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: Self-Stripping Connector with Waterproof Sealant - 14-18 Gauge - White and Blue - Qty 1
- Shop: Combination LED Trailer Tail Light - Submersible - 6 Function - 11 Diodes - Passenger Side
- Shop: Quick Splices - Self-Stripping Connector - Closed Port - 18-22 Gauge - Red - Qty 1
- Shop: Quick Splices - Self-Stripping Connector - Closed Port - 14-16-18 Gauge - Blue - Qty 1
- Search Results: wire
- Video: Optronics Trailer Lights - Tail Lights - STL8RGB Review
- Video: Optronics Combination Trailer Tail Light Review and Installation
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Shop: Brake Controller