Replacement Bar Clamp For Yakima FrontLoader And ForkLift

Question

Question:

Hi, would this also be the right part to replace the rear bar clamp on a Yakima frontloader bike rack # 02103? Yakima lists a replacemt part #8880192 which looks the same as this.

asked by: Per

0

Expert Reply:

If you're wanting to replace the read bar clamp on your Yakima FrontLoader # Y02103, then this is the complete Rear Clamp Assembly # 8880208 but if you think the hardware and clamp # Y8880192 is all you need to replace, we have that as well.

expert reply by: Adam E

0

Answer 1

Yes, the Replacement Yakima Aero Mount Bales #Y8860053 are the same as the bale that comes with the Replacement Hardware and Clamp for Yakima FrontLoader #Y8880192. Just be mindful that those bails don't come with the T-Bolt or the knob so if…

view full answer...

Answer 2

Yes, you will remove the brass nut and bolt and the red knob will come off. You should note that the #8880226 does not come with a new nut (just a washer), so be sure not to lose your current one.

view full answer...

Answer 3

From your statement and the pictures, it looks like you are needing the mounts that allow you to attach the Yakima FrontLoader to the crossbars. If that is the case, we do have the rear mount/clamp. - Replacement Rear Clamp Assembly for Yakima…

view full answer...

Answer 4

For the bolt that is used to close the Replacement Front Jaw #Y8880189 for the Yakima ForkLift Bike Rack #Y02098 you need the Front and Rear Adjusting Handles #8880139 and Replacement T-Bolts #8860061. The bolts themselves are the same size; it's…

view full answer...

Answer 5

According to the folks at Yakima, the front clamp is integrated into the rack and isn't removable, with the exception of the front tensioning handle, which is available as part #8880190. The rear clamp assembly is available as part #8880208. The…

view full answer...

Answer 6

We do carry roof mounted bike racks that will work with thru-axle style bikes, but the SportRack Downshift Plus Roof Bike Rack will not work with thru-axle bikes. Depending on the size of the axle, a bike rack like the RockyMounts SwitchHitter Roof…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Replacement Bar Clamp For Yakima FrontLoader And ForkLift

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching