Replacement For Idler Hub Using 07100 Inner and 07087 Outer Bearings
Question:
Good Evening, I’m working on an old trailer, roughly 4x8. The old hubs required wheels with larger ID hub openings. I’m putting 4.80-12” wheels/tires with a 5-4-1/2 on. Old hubs had inner bearings 07100 and outlets were 07087 with 12437 seal. I can’t seem to find a new hub with these specs. Can you help me out? Thanks
asked by: Levi B
Expert Reply:
Unfortunately, we don't offer any hubs that are compatible with the bearing set you mentioned.
You'll likely find that your best bet would be replace the existing axle with something that uses spindles that are compatible with hubs that use bearings that are more common. If you can provide the hub face to hub face dimension and the center to center distance between the spring seats where the leaf springs attach to the axle, I can check to see if we offer a compatible axle.
Another option would be an axle-less suspension from Timbren,.like part # ASR2KHDS01. This system provides a rubber Aeon spring suspension would allow you to remove the existing leaf springs, which will quiet your suspension considerably. This system uses a standard spindle that's compatible with an easily obtainable standard 3500 lb capacity idler hub like # AKIHUB-545-35-EZ-K. The hub includes the bearings, races, grease seal, lug nuts and grease cap.
I've linked to a product demonstration video for the Timbren Axle-Less suspension I mentioned above.
Products Referenced in This Question
Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Timbren Axle-Less Trailer Suspension - Heavy Duty - No Drop - 4 Bolt Flange - 2,000 lbs
- Trailer Axles
- Rubber Spring Suspension
- Easy Lube Spindles
- No Hubs
- 2000 lbs
- Spindles Only
- Universal Fit
- No Drop or Lift
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Q&A: Replacement Hub for 2002 Coleman Niagara Pop Up Camper
- Q&A: Recommended Timbren Axle-Less Suspension With Compatible Idler Hub Assemblies
- Q&A: Replacement Idler Hub for J.Q. Tex Marine Trailer With 3,500 Pound Axle
- Shop: CE Smith Trailer Axle Beam with Standard Spindles - Galvanized - 57-1/2" Long - 1.8K
- Shop: Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Video: Review of CE Smith Trailer Axles - Leaf Spring Suspension - Square Trailer Axle - CE33201GA
- Shop: Double Lip Seal for 3,700-lb Marine Hubs
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Shop: Trailer Hitch
- Search Results: 44649
- Shop: Grease Seals 10-36 (pair)
- Shop: Trailer Wiring
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Search Results: 25580
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: Most Popular Wheel Bearings
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Search Results: 68149
- Shop: Fifth Wheel Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Video: Choosing the Right Brake Controller
- Shop: Brake Controller
- Search Results: dust cap