How to Determine the Correct Wheel Chock for a Keystone Bullet 281 bhs

Question

Question:

Please advise, which size I should order for a keystone bullet 281 bhs

asked by: Scott

0

Expert Reply:

Most of the wheel chocks on the market are universal items and not trailer specific. To determine which Ultra-Fab Chock and Lock Wheel Stabilizer will work best for your Keystone Bullet 281 bhs, we will want to know the spacing between your tires (see photo). The Chock and Lock Wheel Stabilizer, # UF21-001060, will expand up to 5-1/4 inches wide and it is available as a two pack as part # UF21-001070.

If your tires are further apart, then you could use the Chock and Lock Wheel Stabilizer, # UF21-001080. This stabilizer is adjustable up to 10 inches wide.

I have attached review videos of the wheel stabilizers for you to check out.

expert reply by: John H

0

click to enlarge

Answer 1

The Stromberg Carlson Replacement Motor #LG-196308 and the Lippert HD Motor #LC196308 referenced in your question are essentially the same motor. They can be used interchangeably on a landing gear system. With this in mind, I simply recommend…

view full answer...

Answer 2

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 3

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 6

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 7

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 8

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

You will need the Ceiling Garnish for Fan-Tastic Vents Roof Vent #FVK1060-81 as it is specific to your Dometic Fantastic Fan 1450. The Ceiling Garnish for Ventline Roof Vent #VA0445-37 is going to have rounded corners as opposed to the square on the…

view full answer...

Answer 11

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 12

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

How to Determine the Correct Wheel Chock for a Keystone Bullet 281 bhs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching