Does Draw-Tite Trailer Hitch Receiver Fit 2019 Subaru Crosstrek Hybrid

Question

Question:

Hi. I have a 2019 cross trek hybrid. Will the draw tire hitch fit on the cross trek hybrid? I see that it does fit the regular cross trek but wanted to confirm it will work on the hybrid. Thanks

asked by: David C

0

Expert Reply:

I was able to confirm with Draw-Tite that they do have a trailer hitch receiver which is a confirmed fit for your 2019 Subaru Crosstrek hybrid, which is the following hitch:

- Draw-Tite Max-Frame Trailer Hitch Receiver # 36644

expert reply by: Kyle S

0

Answer 1

We haven't had any ground clearance issues with any of the trailer hitches we offer for your 2018 Subaru Impreza including the Draw Tite part #36644 that you mentioned. When we installed the 2 inch hitch part #76209 on a 2018 Impreza like yours…

view full answer...

Answer 2

I checked with Draw-Tite and can confirm for you that the Draw-Tite Trailer Hitch #36644 you asked about will fit your 2019 Subaru Crosstrek hybrid. I attached an install video for this for you to check out as well.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The Draw-Tite Class II #36644 hitch fits the 2018 - 2021 Subaru Crosstrek and the 2018 - 2021 Subaru Impreza 5-Door Wagon with Single Exhaust.

view full answer...

Answer 5

Installing a wiring harness, like the Tekonsha T-One Vehicle Wiring Harness #118467, on your 2020 Subaru Crosstrek will require access/removal of a few panels in the rear cargo area. I included an install video for you to check out that will…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Does Draw-Tite Trailer Hitch Receiver Fit 2019 Subaru Crosstrek Hybrid

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching