Replacement Spindle Washer for Axle with Bearings that are 1-3/8 and 1-1/16 inch

Question

Question:

Good afternoon, I am looking to buy some tang type spindle washers. The hubs I have on my trailer are 1 3/8 x 1 1/16 spindle. Would the 1 inch inner diameter tang type washer fit my spindles?

asked by: Colton B

0

Expert Reply:

Based on the spindle dimensions you have the tang washer you'd need is the part # 5-71.

expert reply by: Jameson C

0

Answer 1

Since the Dexter 10k axles have a 1-1/2 inch threaded diameter the correct replacement nuts would be the #6-96. The tang washer you could use with this would be #5-59.

view full answer...

Answer 2

I checked with Dexter and here is the information on tightening the spindle nut on your 8K axle: 1. After placing the hub, bearings, washers, and spindle nut back on the axle spindle in reverse order as detailed in the previous section on hub…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Replacement Spindle Washer for Axle with Bearings that are 1-3/8 and 1-1/16 inch

Product Page this Question was Asked From

Continue Researching