Correct Replacement 10 Amp Hour Battery for Bright Way Push-to-Test Trailer Breakaway Kit

Question

Question:

I am not seeing the replacement 10ah battery on your site, do you offer it?

asked by: Dan

0

Expert Reply:

The correct replacement battery for the Bright Way Push-to-Test Trailer Breakaway Kit with 10-Amp-Hour Battery part # 3802311 is the Replacement 10-Amp Hour Breakaway Battery part # BRW87FR .

expert reply by: Conner L

0

Answer 1

The battery you use for a break away system needs to be able to power the trailer brakes on full for 15 minutes. A 12 volt battery rated for 5 amp hours is normally used, unless you have 3 axles each with brakes, then you would benefit more from a…

view full answer...

Answer 2

The Bright Way Push-to-Test Trailer Breakaway Kit #3802311 that you referenced comes with a 10 amp hour battery. I attached a picture of the battery outside of the box for you to check out as well. I attached a review video for this kit for you to…

view full answer...

Answer 3

It sounds like you may have the power and ground wires reversed. I have included an image below for the terminals on a 7-way connector so you can verify you are connecting to the correct wires on your trailer connector. The power terminal is located…

view full answer...

Answer 4

If your breakaway battery is dead, your brakes should operate while connected to your vehicle's 7-way trailer connector. If your brakes are not operating, then it sounds like you might have a short in the brake wiring of the trailer. Battery…

view full answer...

Answer 5

I just called my contact at Titan and they told me that you should never use the DOT 5.1 fluid. They said if DOT 5.1 is used it will reduce the life of the seals in the unit by about 75 percent. They told me that there is a typo in the instructions…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Correct Replacement 10 Amp Hour Battery for Bright Way Push-to-Test Trailer Breakaway Kit

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching