Bolt Hole Dimension of Buyers Products Black Receiver Tube 3371804055

Question

Question:

The horizontal bolt hole dimension in the product pictures shows 3 1/2inch but in one of the question answers it shows 3 3/8. Which is correct?

asked by: Bob

0

Expert Reply:

The Buyers Products Black Receiver Tube part # 3371804055 has a vertical set of holes which are 3-1/2" apart on center and a horizonal set which are 3-3/8". I have attached a dimensions drawing from the manufacturer below.

expert reply by: Conner L

0

click to enlarge

Answer 1

From center to center, the bolt holes on the Buyers Products Black Receiver Tube #3371804055 measure 3.5" vertically and 3.38" horizontally, as you can see in the accompanying photo.

view full answer...

Answer 2

The Demco Channel Tongue Trailer Coupler - eZ-Latch - Silver - 2" Ball - Bolt On - 10,000 lbs #DM15000-52 is a bolt on coupler for a pole tongue trailer. It is compatible with 3 inch channel width and has bolt holes in the spacing I've…

view full answer...

Answer 3

The mounting plate of the Buyers Products Black Receiver Tube #3371804055 measures 6" x 5"; the plate itself is 1/2" thick.

view full answer...

Answer 4

On Draw-Tite ball mount #2793, from the center of the hitch pin hole to the nearest part of the support gusset it is 4 inches. From the center of the hitch pin hole to the furthest part of the gusset is approximately 6-1/2 inches.

view full answer...

Answer 5

I've drawn up a little diagram below of the Hughes Autoformers Safe View Smart Power Inlet #HU87VR dimensions. Based on what I found a 3-1/2" round hole would be a bit too large and would require you to first place some sort of cover over…

view full answer...

Answer 6

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 7

Thank you for providing the replacement vent lid part number VA530. This was indeed once a valid part that is now obsolete, but we can still help you select a replacement vent lid. Please refer to the linked photo showing the different hinge styles…

view full answer...

Answer 8

The CE Smith U-Bolt Kit for Mounting 1-1/2" Square Trailer Axles #CE23102 that you referenced includes two u-bolt plates, 8 nuts and washers, and 4 u-bolts. In other words it comes with two sets and not just one like you asked.

view full answer...

Answer 9

I took a look at the online owner's manual for your 2017 Honda Fit EX. It starts off by stating that only the manual transmission models of the Honda Fit can be towed behind a motorhome with all four wheels on the ground. For extended towing…

view full answer...

Answer 10

The Gorilla-Lift Replacement Roller Assembly, part #GMNR925, consists of two each of the rollers, pins and clips along with four washers. The rollers themselves are machined from a high-density hard thermoplastic compound similar to nylon. The…

view full answer...

Answer 11

You could certainly reverse the position of the lamps by installing the #328-003-81LBM1 lamp on the passenger side and the #328-003-81BM1 lamp on the driver's side. Both lamps wire the same way, the white wire is the ground connection, the red is…

view full answer...

Answer 12

I spoke to my contact at Curt and he informed me that from the center of the mounting holes that are on the mounting bracket on top of the hitch opening to the end of the opening measures 1-1/2 inches.

view full answer...

Bolt Hole Dimension of Buyers Products Black Receiver Tube 3371804055

Product Page this Question was Asked From

Continue Researching