Baby Moon Hub Caps Fit on Conventional Steel Trailer Wheels

Question

Question:

What is a five lug tire with an extra tip/ nipple called and where can I get them?

asked by: Jim R

0

Expert Reply:

It sounds like you are talking about a conventional steel wheel. These wheels have a raised section, see picture I have included, that a baby moon hub cap, # AM90086, will fit onto.

There are different sizes available in the conventional steel wheels. To get the correct one I would need to know the bolt pattern, the width, and diameter you need. I have included a link that shows how to measure for bolt pattern.

expert reply by: Michael H

0

click to enlarge

Answer 1

The correct baby moon hubcaps for the Dexstar Conventional Steel Wheel with Offset part #AM20504 is the Americana Baby Moon Trailer Wheel Center Cap part #AM90086.

view full answer...

Answer 2

The wheel used on the #AM32395 Karrier 205/75-15 wheel doesn't have the retention clips or nubs stamped into it that would hold a hubcap in place (see photo). I have some options for you though. A conventional steel wheel like what's…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Baby Moon Hub Caps Fit on Conventional Steel Trailer Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching