Hardware Grade of Install Hardware for Curt Hitch 13534

Question

Question:

What material are the bolts made, and what rating are they and what finish on the bolts

asked by: Bernardo

0

Expert Reply:

The install hardware of the Curt hitch # 13534 are Grade 5 steel bolts in the size of M10x1.25. They are zinc coated.

expert reply by: Jameson C

0

Answer 1

The torque specs for the Curt Trailer Hitch Receiver #13534 (that fits a 2008 - 2013 Toyota Highlander) can be found as step 5 on the second page of the attached installation instructions. Sometimes manufacturers might swap hardware out so that the…

view full answer...

Answer 2

Apparently, on the 2014 Chrysler Town and Country, on the passenger side frame rail there is a bolt that is holding on the bumper and it should not or cannot be removed. Otherwise there would likely be 6 bolts instead of 5 holding on Curt trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

We do offer replacement hardware for the Curt Trailer Hitch Receiver part #13534. Just enter part #RHK in the search box on our website. Then enter 13534 in the Hitch Item Number box. Select Curt From the dropdown box and order it. Your hardware kit…

view full answer...

Answer 5

Good news. We do sell just the hardware for the Curt Class III Hitch #13534. The replacement hardware kit part number you will need is #RHK. On this page, which I've attached to this page for you, will have a box where you will need to enter in…

view full answer...

Answer 6

You'll need (6) M10 - 1.25 x 30 Class 10.9 hex bolts and (6) 3/8 inch conical toothed washers. We offer them in the #RHK kit you'd looked at, On the product page, you'll input the hitch part number and choose the hitch manufacturer from…

view full answer...

Answer 7

Most Vehicles and hitches have their own specific hardware to insure proper fit and towing capacity. Our #C13149 hitch includes a hardware kit and installation guide. I attached a video on the installation for your convenience. The hardware specs can…

view full answer...

Answer 8

Sometimes hitches can get slightly bent during shipping and this can be fixed by bending the hitch back into place as long as the hitch only has a slight bend to it. If the #13534 wasn't lining up I can almost guarantee that is what happened.…

view full answer...

Answer 9

Sometimes hitches can get slightly bent during shipping and this can be fixed by bending the hitch back into place as long as the hitch only has a slight bend to it. If yours isn't lining up I can almost guarantee that is what happened. Some…

view full answer...

Answer 10

With trailer hitch receivers that have brackets like the Curt #13555 receiver that you purchased for your 2009 Honda CR-V, it is not uncommon for those brackets to get slightly bent during the whole shipping process. If you wanted to return it there…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Hardware Grade of Install Hardware for Curt Hitch 13534

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching