Is Bumper Trimming Required to Install Curt Trailer Hitch 11091 on a 2009 Volkswagen Passat
Question:
Do you have to cut the molding on the rear bumper to install.
asked by: Stephen S
Expert Reply:
There are 3 areas that you will need to trim on an under-body panel on the 2008 VW Passat to install Curt trailer hitch # 11091. These areas are under the vehicle, parallel with the ground and not on the back vertical part of the fascia. I have included a link to the installation instructions which include a diagram that shows the areas that need to be trimmed.
This hitch comes with the correct ball mount, pin, and clip. If you plan on doing some towing you can use 1-7/8 inch ball # 19256 or 2 inch ball # 19258. For trailer wiring use # 119250KIT. I have included a link to the installation instructions for the wiring as well.
A power wire connection to the battery is required for the wiring to work. The trailer will be drawing power from the vehicle battery. This protects the vehicles sensitive wiring and electronics. I attached an informational video for you.
Products Referenced in This Question
ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Spare Parts for Harbor Freight HaulMaster Utility Trailer 90154
- Article: Trailer Tire Sizing
- Q&A: Trailer Hitch Receiver For 2021.5 VW Atlas SELP For Carrying Bike Rack
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Recommended Trailer Hitch Fit for 2008 Volkswagen Passat Wagon
- Article: Roof Rack Information
- Q&A: Are There Replacement Brake Pads for the Tie Down Engineering (TDE) 46304 Disc Brake Calipers
- Q&A: Way to Transport Dirt Bike with Class I Hitch
- Q&A: Can I Carry a Dirt Bike on a 1-1/4 Inch Hitch with a 2-Inch Hitch Adapter on a Honda Accord?
- Q&A: Which Curt Trailer Hitch for 2017 Toyota Sienna is Concealed