Parts Interchangability for a Roadmaster Base Plate Kit on My 2009 Honda Fit

Question

Question:

I use a Roadmaster hitch to tow my 2002 VW Beetle and have kit number 521225-1 installed that vehicle. I am trading it in on a 2009 Honda Fit and understand I need kit number 521190-1 for the Honda. My question is: is the draw bar portion of the kits interchangeable and, if so, could I purchase just the portion of the kit that bolts to the new vehicle. That way I could use the draw bars off my VW on the Honda. They look the same in the drawings but, I thought I better check first. PS: If this will work, can you sell me a 521190-1 without the draw bars?

asked by: Lloyd

0

Expert Reply:

The Roadmaster EZ Base Plate Kit, part number 521190-1, is the correct kit for your 2009 Honda Fit.

I am sorry but the base plate kits are sold only as a complete set. When the kits are manufactured the brackets are universal fit but the draw bar portion of the kit, while being very similar part to part, are specifically matched, for that base plate kit only. We do not sell the vehicle side brackets only.

expert reply by: Robert G

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 3

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Parts Interchangability for a Roadmaster Base Plate Kit on My 2009 Honda Fit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching