Is There a Lock to Secure Demco Above Bed Autoslide Hitch to Rails

Question

Question:

Is there a way to secure it to the bed? Theft protection??

asked by: Jim

0

Expert Reply:

We have fifth wheel base rail locks like the part # TR63254 which you could use as a theft deterant with the Demco fifth wheel hitch part # DM8550034.

expert reply by: Jameson C

0

Answer 1

The cone that you see in the picture you attached of the Curt Crosswing part #C86JR is there to help align it with the rest of the hitch when you back the vehicle up into it and lower it down with the jacks. This ensures it is completely seated and…

view full answer...

Answer 2

Yes, the Curt CrossWing Lightweight 5th Wheel Trailer Hitch #C86JR will work just fine with the Curt Flex Air 5th Wheel Pin Box #LC328492. This pin box has a maximum towing capacity of 18,000-lbs, an internal air bag that reduces air shock, and and…

view full answer...

Answer 3

The E6 error you are getting from the Furrion RV Tankless Water Heater #FR93FR could be from a variety of different things. I have added a cut out from the manual which goes over what the E6 error code means. It is unlikely you need to change your…

view full answer...

Answer 4

Yes, the Curt CrossWing Lightweight 5th Wheel Trailer Hitch #C86JR that you referenced can be used with fifth wheel trailers that have cushioned pin boxes.

view full answer...

Answer 5

That's a good question but we don't have a way to look that up since Winnebago does not list that as a spec anywhere. You'd have to measure and verify before ordering either the 3 inch #F02-2106 or the larger size #F02-2103. Since the 3…

view full answer...

Answer 6

The Furrion cameras, like what comes in the part #FOS43TASF that replaced the part you referenced, are only compatible with their specific monitors. If you are looking for a camera system that allows you to use your smartphone as the monitor then I…

view full answer...

Answer 7

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Is There a Lock to Secure Demco Above Bed Autoslide Hitch to Rails

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching