How To Measure for Round SnapPad Jack Stand Pads

Question

Question:

how do you measure? I measured and got 9 in front and 12inches in back. Thor Tuscany 40rt 2020

asked by: Steve

0

Expert Reply:

In regards to the SnapPad Jack Stand Pads, if you have round shaped feet then you would measure the diameter from end to end. If the feet measures 9" then you can use part # SP54FR2. I have attached a full list of options below but there are no options for 13" diameter feet.

expert reply by: Conner L

0

Answer 1

The bottom portion of the SnapPad Jack Pads #SP54FR2 are approximately 1" thick but they are not meant to lift your wheels off the ground. If your wheels came off the ground that would mean you're putting the full weight of your RV onto the…

view full answer...

Answer 2

That's a good question and the difference between the two SnapPad Jack Stand Pads for Motorhome are different shapes and depths, it isn't solely the notch in the center. I added photos of the two pads side-by-side so you can see the…

view full answer...

Answer 3

They can be! For a single 9" round SnapPad, like what you referenced in part #SP54FR4, you'll need the part #SP54FR.

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

How To Measure for Round SnapPad Jack Stand Pads

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching