Quick Links Needed for 10,000 lb Trailer

Question

Question:

Hi. I see you have towing safety cables rated for a 10,000 pound trailer. I am looking for just the quick links that are rated at 10,000 lbs. My cables are fine. Do you carry them? Thanks.

asked by: Jeff M

0

Expert Reply:

Sounds like you're looking for the Blue Ox 1/2" Quick Link for Safety Chains # BX229-0512. This is designed for the Blue Ox Safety Cables # BX88197 and # BX88208 which are rated for 10,000 lbs, but it will work with any other type of chain or cable as well.

expert reply by: Jon G

0

Answer 1

When using D-ring adapters to flat tow your Jeep like what it sounds like you're doing, safety cables will generally just need to be attached to the vehicle's frame. What you can do is use some short cables to wrap around each frame rail and…

view full answer...

Answer 2

I would be happy to help! Since you will be installing the Blue Ox Aftermarket Off-Road Bumper Adapter for 7/8" pins #BX88357 on your 2009 Jeep Wrangler Unlimited I recommend going with the Blue Ox Alpha 2 Non-Binding Tow Bar #BX7380. This tow…

view full answer...

Answer 3

A horizontal band saw with a blade that can cut steel would be your best option. But even a cutting wheel with a thin disc would work pretty well too. If you have access to a sawz-all that would be an option. But I would go with the first two options…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

On equalizer 013-105-04 in kit #K71-360-00 the eye center to eye center measurement is approximately 7-1/2 inches.

view full answer...

Answer 8

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 9

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 10

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 11

There are and were numerous 2-step Kwikee electric steps available. To ensure we get you the correct replacement I would need to know the series of the steps you have. Check the underside of your steps for any model numbers or other information. The…

view full answer...

Answer 12

It is really not a great idea to drive with a trailer cover like the part #052963735635 installed on a trailer. The only way I could safely recommend you do so is if you were to keep the speeds under 25 miles per hour and you weren't on a public…

view full answer...

Quick Links Needed for 10,000 lb Trailer

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching