Correct Replacement Light Strip for Awning On Winnebago View

Question

Question:

We have a 2015 Winnebago View 24V with a 16foot awning. The factory installed LED strip installed on the outside edge of the awning has many non working diodes. Will this work as a replacement strip?

asked by: John

0

Expert Reply:

If you have a Lippert Solera Awning then the Replacement LED Light Strip part # LC423331 is what you will want to use as it is the correct width that is needed to fit inside the channel. It can be cut to fit the exact length you need.

The LED Light Strip part # DG52681 is slightly smaller width wise than the above so it may not work.

expert reply by: Conner L

0

Answer 1

The correct replacement LED strip for your Solera Awning is the Replacement LED Light Strip for Solera RV Awnings #LC423331. This LED strip measures 20' long so it'll work fine with your 17' awning.

view full answer...

Answer 2

I contacted Diamond and the LED strip part #DG52681 can only be cut into two sections because the 4-pin connectors are not sold separately. When you cut on one of the copper sections of the strip you will be able to slide the 4-pin connector into…

view full answer...

Answer 3

Yes you can expand the Diamond LED light strip part #DG52681 that you referenced. We have strip connectors for this light with part #DG52675PB as well as expansion strips like the #DG52697 which would add 33 feet.

view full answer...

Answer 4

The best solution for ride quality and stability for your 2017 Winnebago View 24J will be with a SumoSpring #SSA11MTKT installed. This gives better suspension support that translates the best into improved handing, comfort, and support. Scissor jacks…

view full answer...

Answer 5

The awning light strips we carry are designed to fit into slots that are on the fabric rollers of the awning. But we do have awnings that attach to the RV with adhesive like with the part #LC24PJ.

view full answer...

Answer 6

To disconnect the awning fabric that is connected to the trailer, you will simply slide it out of the awning rail extrusion like #LC715217. I've attached a couple videos of the installation to help. Removal is simply the same in reverse and…

view full answer...

Answer 7

First of all your tire size, 215/85-16 sounds like it's a passenger vehicle tire and not a trailer tire. Trailer tire sizes begin with "ST" for special trailer. I recommend using ST tires because they have a stiffer sidewall to handle…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Correct Replacement Light Strip for Awning On Winnebago View

Product Page this Question was Asked From

Continue Researching