Availability of 63" Replacement Pitch Arm Assembly for Solera Standard Flat Awning

Question

Question:

Do you have just the pitch arm for a 63inch instead of a 69? This is for the awning that is attached to our slide out. Thanks

asked by: Jessica B

0

Expert Reply:

We do have the Replacement Pitch Arm Assembly for Solera 69" Standard Flat Awning Support Arm - Black # LC375994 in a 63" version for you. We have it listed as part # LC67VR on our site!

expert reply by: Jon G

0

Answer 1

When installing The Replacement Pitch Arm #LC375994 you will need to use three of the retaining washers #LC431583. I attached a review video link below.

view full answer...

Answer 2

Thank you for the pictures and the measurement. The correct replacement pitch arm is the Replacement Pitch Arm #LC375994. The Replacement Pitch Arm #LC375994 is 31-1/2" long and is for the 69" long support arms like the measurement you…

view full answer...

Answer 3

When your current pitch arm is folded out and fully extended measure it's overall length. If it's 69 inch it would be the part #LC375994 for a replacement or if it's 63 inches #LC97UD.

view full answer...

Answer 4

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 8

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Answer 9

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 10

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Answer 11

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 12

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Availability of 63" Replacement Pitch Arm Assembly for Solera Standard Flat Awning

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching