Spindle Nut That is Slightly Larger Than 3/4 Inch

Question

Question:

I have a 1996 procraft 3500 lb trailer What size nut and retainer do I need ? I picked up 3/4 inch and it’s just A bit to small

asked by: Jim B

0

Expert Reply:

Although we don't have any way of knowing the spindle nut you need for your trailer, we do have something slightly larger than 3/4 inch diameter which may work, the 7/8 inch Spindle Nut # 165931.

expert reply by: Kyle S

0

Answer 1

I reached out to the manufacturer who told me the Spindle Nut for Axles with 7/8" - 14 Castle Nut #165931 height is 3/4 inch and wrench size is 1-1/4 inch. I've added a link to a video review for you to check out as well.

view full answer...

Answer 2

I have been unable to locate a spindle that meets the exact specifications that you have on your current spindle. The #42 Spindle #TRU57FR will be the closest that I can find to matching your current spindle. It is 2.25" diameter, rated for…

view full answer...

Answer 3

There is no specific torque rating when reinstalling the castle nut after packing the bearings. You want to run the nut down until there is no side to side play in the hub, and then back it off to the next notch in the castle nut so the retainer can…

view full answer...

Answer 4

We have a few options that could work for you, but you will need to measure the threads of your spindle to determine which would work. For a 1 inch spindle nut you would need the part #165686, for a 7/8 inch nut you would need part #165931. These are…

view full answer...

Answer 5

To verify if your hubs on your 6,000lb Dexter axles are going to fit the etrailer AxleTek 7,000LB Axle #e35GR you will need to verify what bearings and grease seals are used on your hubs. The new axles will use a #42 Spindle #TRU57FR, and this is the…

view full answer...

Answer 6

I would be happy to help you fine the correct replacement wheel bearings for your 2006 YachtClub Jet Ski Trailer with hubs that have the 5 on 4-1/2" bolt pattern, but the part number you mentioned does not cross-reference to anything so you will…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Spindle Nut That is Slightly Larger Than 3/4 Inch

Product Page this Question was Asked From

Continue Researching