What HappiJac Anchors Work With my 2012 Ram 1500

Question

Question:

Hi , i recently purchased a new truck and I would like to use my happyjack tie down system I currently have, I need new anchor plates for a 2012 dodge 2500, what is the correct anchor plate I would need?

asked by: Les W

0

Expert Reply:

For use on all models of the 2012 Ram 1500 the HappiJac Custom Tie-Downs for Truck Bed Camper part # LC236326-205221 is exactly what you want.

expert reply by: Randy B

0

Answer 1

The best air bag suspension enhancement for your 2020 Ram 1500 4x4 are the Air Lift LoadLifter 5000 Air Helper Springs #AL57375. These are the best for your Ram because they have the highest capacity at 5,000 lbs and do not either replace your coil…

view full answer...

Answer 2

The Brophy Clamp On Camper Tie-Downs #HSAB are not designed as specific fits for a truck, so there is no information regarding their fit on a 2016 Ram 1500 with a 6'4" bed, but I can tell you how to determine it they will. The Brophy…

view full answer...

Answer 3

If your 2014 Ram 1500 does not have a running board or step under the bed and a factory hitch then you can use the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLD2134 with the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear…

view full answer...

Answer 4

Yes, the Happijac Tie Down Setup part #LC236326-205221 that you referenced does fit the 2022 Ram 3500 that has the deployable step in the rear bumper so this kit would work great for your customer.

view full answer...

Answer 5

I recommend the TorkLift Talon Custom Frame-Mounted Camper Tie-Downs - Aluminum #TL94FR front and #TL34FR for the rear. These rustproof and lightweight aluminum alloy tie-down inserts secure to durable stainless steel receiver brackets. The tie-down…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What HappiJac Anchors Work With my 2012 Ram 1500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching