Looking For Reversible MaxxAir RV Roof Vent Fan

Question

Question:

I couldnt find any info as to whether the fan can function both as an exhaust as well as pull air in from outside. The older model 4000 did this, and I dont believe it is available anymore so I am looking for the next best thing. Thanks!

asked by: Zachary S

0

Expert Reply:

The MaxxFan # MA00A04301K you referred to isn't reversible, it will exhaust only.

If you want a reversible fan, you'd need to go with the MaxxFan Plus, part # MA00-04002K. This fan is reversible and can operate manually or by using the preset 78° thermostat.

The 4000K model is still available as part # MA00-04000K, it features a 10 speed fan, versus the 4 speed offered by the # MA00-04002K. I've linked to product description videos for both vent fans

expert reply by: Mike L

0

Answer 1

Thank you for your purchase from etrailer of the Valterra Bladex Waste Valve Body for RV Black Water Tank - Plastic Handle - 3" Diameter #T1003VP. As you can see from the accompanying photo, it is normal for their to be a little space on each…

view full answer...

Answer 2

Yes, we have confirmed with Maxxair that the replacement circuit board part #MA10A21276K is the correct part number for your #MA00-04000K.

view full answer...

Answer 3

There are only two wires on the Fan-Tastic Vent Roof Vent w/ 12V Fan part #FV801208, a white wire which is the ground and then a black wire which is the power. The ground wire will need to be ran to a bare metal surface and the power wire will need…

view full answer...

Answer 4

You'd need to use a converter like the part #34266168 to convert the 110 AC power of your trailer to a 12 volt source that could power your roof vent.

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

Yes most of the T@G campers I have seen use the Yakima 54" Tracks for Roof Racks part #Y01127 base tracks. You can get evrything you need in one kit with the Yakima HardTop SL Roof Rack - 60" CoreBar Crossbars - 54" Tracks part #Y01618…

view full answer...

Answer 7

The Draw Tite #75601 and the Curt #13358 that you referenced both are a fit for your 2017 Mercedes Benz Sprinter 2500. They have very similar ground clearance but the Curt has the slight edge as it seems to sit a bit higher. I attached a picture that…

view full answer...

Answer 8

There isn't going to be any noticeable difference in the fit between the Draw-Tite Trailer Hitch #75549 and Curt Trailer Hitch #C13388 that fit your 2019 Mercedes-Benz Sprinter 2500 with a 170 inch wheelbase and standard bumper. The reason for…

view full answer...

Answer 9

If you have more of the weight in the trailer on the left side then that could explain the uneven wear. Axles have a bow or camber in the middle. When weight is in the trailer it straightens out the axle some and the tires should wear evenly. When…

view full answer...

Answer 10

The Dexter E-Z Flex Suspension Kit part #K71-653-00 will work just fine on 3,500 axles assuming the measurements match up which in your case they do. I have spoken to Dexter about this before and the weight capacity listed is more or less a guide to…

view full answer...

Answer 11

The Replacement Control Module for Lippert Electric Coach Step #LC301702 is the brain for your coach step with serial number 06190. We also have the following parts for your coach step: Replacement Motor for Lippert Electric Coach Step #LC301695…

view full answer...

Looking For Reversible MaxxAir RV Roof Vent Fan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching